One is for oil obese patients controlled at grams per day

Only when energy intake is insufficient , will consume the body fat accumulation . Therefore, to reduce energy intake , especially fat intake, can achieve the purpose of weight loss .  feed equipment dietary obese people mainly vegetable oil should be less saturated fatty acids , the amount of edible oil to control the total energy does not exceed 10% , i.e., the amount of edible oil per day at about 30 g for the control well .
Briquette machine edible hydraulic press squeezing process, we need to pay attention to this aspect so as to allow us to write advanced hydraulic press to squeeze out the oil to eat healthier more valuable and more !

Sawdust rods machine maintenance

1 , bearing shoulder the entire load of the machine, so good lubrication of the bearing life of a great relationship , it directly affects the life and the operation rate of the machine, thus requiring the injection of oil must be clean , seal must be good , the machine Oil machine oiling Office ( 1 ) Turn the bearing ( 2 ) roller bearing ( 3 ) All gear ( 4 ) activities bearing , sliding plane.
2 , the newly installed tires prone to loosening must always be checked.
3, note that the various parts of the machine is working properly .
4 , pay attention to check the degree of wear of wear parts , pay attention to the replacement of worn parts .
5 , put the activities of the device chassis plane should avoid activities out dust and other materials bearing on the bottom shelf can not move the machine could not have broken the material ,oil expeller in a serious accident.
6 , rotating gears in operation should be immediately stopped if the impact of the sound check and eliminate .
7 , bearing temperature rise , the reasons should be eliminated immediately stopped and checked .
Sawdust rods machine maintenance is an extremely important regular work , it should work closely with the operations and maintenance and other extremely , full-time staff should be on duty checks.

Ordinary virgin after rolling press materials

Ordinary virgin after rolling press materials , by-products as animal feed only after the machining, such as every hundred pounds of peanuts to squeeze 28 - 35 pounds of oil , peanuts can also be processed into high-protein restitution low- fat green food, such as processing spicy peanuts, Feed plant , peanut tofu, artificial meat , peanuts, pickles , peanut candy ﹑ peanuts and other peanut products . Higher value-added products .
Three lossless : Normal spiral extrusion seed oil press to produce high temperature , the oil nutrition reduce raw material consumption by 6% , the machine adopts physical crushing , no heating , no lossy , adjustable oil yield , oil can compared with the name brand beauty.

Press completely rely on pure physical extrusion machinery

Small automatic oil completely rely on pure physical extrusion machinery , without any chemical solvents , and thus retained the overall plant nutrients and authentic , its rich aroma , pure taste, oil refinery, purely a " green, natural, nutrition, healthy oil , "we uS Genesis press after a long market survey and research , research and development of advanced automation equipment for small and medium automatic press , won many national honors and patents, plant oils and fats the quality of the merits , but also on the sensory identification can be broadly summarized as color, odor , taste and other items, combined with the promotion of transparency , water content, sediment and seed oil extraction comprehensive judgment. Grossly oil color which is normal , with or without impurities or sediments, whether there is mold sniffing coke , rancid taste, mouth taste is bitter , spicy , sour and other odors, is to identify key indicators of good or bad vegetable oils . Vegetable oils can also be heated test , thick and choking fumes when a fat rancidity.

Press common troubleshooting method

1 when no suction pump overhaul , the case of dirt clogging oil network, washable grease filter should be . If the oil is used for a long time , due to sediment adhering to the inlet valve and the valve does not cause adhesion , should be replaced with a new release of oil or vegetable oil plant and clean the inlet valve . If the fuel tank is not enough , add a little oil to the tank can be , if the vacuum pump in the minors , you can pull out the small piston , and then injected into the oil pressure .
2 When the pump pressure is insufficient maintenance, if there is dirt or poor sealing valve , after grinding them washable , so close together. Press the case of the inlet valve plug and seat is bad, too polished to be washable , so close together. The case of press out the oil drain plug and valve seat caused by poor contact or tighten the oil spill , may press grinding valve plug and seat aspirant so close together or tighten the plug. Briquetting machine of a small pump worn piston and the gap is too big , should be replaced with new pump.
3 When the cylinder and piston leak repair, if installed the wrong sized cup is due up , press the right approach should be re-installed cups . Cup cracked the case of damage , should be replaced with new cup .

Peanut oil press safety technology and maintenance

1 This machine uses 380 -volt electrical and mechanical power , heating and control system uses 220 -volt power supply , according to customer requirements, but also can be changed to 220 volt power supply.
(2) To ensure the safety of electrical systems must be grounded protective measures.
(3) The system is a high pressure corn grinder pressure of 55 MPa pressure levels overpressure is prohibited to use ! Prohibit unauthorized transfer chaos , chaotic demolition !
4 . The case of gauge ineffective or corrupt to be allowed to start production of the non- replacement of the gauge and then boot .
5 high-pressure machine during maintenance and packing machines are not allowed .
6 Please operate in strict accordance with the rules to use during operation.
7 must take after a good fry oil fumes drained gas eruption there would be squeezed poise , and in severe injury.
8 After the oil drained , they should immediately pellet mill machine , otherwise it will be too long gas erupted phenomenon .
9 If the sump blockage please clean up with a thin blade or needle scraping through
10 The new machine uses a hydraulic oil must be filtered month and replace the hydraulic oil clean and clean the tank once a year later . A long time do not use turn off the power.

How to make peanut oil press process like

Multifunctional cold pressed peanut oil press oil technology compared with the current high temperature pressing or extraction process , a simple process , energy saving, less investment in equipment , Briquette machine comparable factors, as well as its effects are not comparable .
First, the double helix cold pressing machine, no need to add peanut shells as a secondary virgin material, and thus get a better peanut pressed cake .
Secondly , the process to achieve low temperature pressing , the most Oh process , high temperature less than 80 ℃, under seed oil extraction . You can get high-quality peanut oil.
Third , you can get the cold pressed peanut cake was crushed crude protein content of 50-60 % high-quality protein powder , is further converted into food with a protein basis.

hydraulic press during operation

Hydraulic press during operation should always check out the press cake cases and controls billet is neither too high nor too low moisture . The cake should be normal flaky , pressed by the screw shaft side smooth , the other side has a lot of hair pattern. If the cake wire stripping machine, or a shapeless cake , darker color , hand pinch Serve fragments , indicating that add little water blank ; such as the cake soft, flaky increase in National Cheng Kung University , or the oil bubble, Minga said that too much water . Under normal circumstances, no or very little residue circular row between the slag , slag in place of discharge , such as slag was fine flakes description pellet machines, the powder residue then the less moisture. In addition, the position of the oil changes can be squeezed out of the water to see if appropriate , when pressed into the water is too high or too low , the oil locations are backward .